OPTIM 1 Surface Cleaner & Disinfectant Wipes, (One can = 160 sheets, each sheet 15 x 18 cm)

10 €
30-60 second kill time!
In stock
Product Details
Marque: SciCan
Units in product: One can = 160 sheets, each sheet 15 x 18 cm
Price per unit: 10€ per can


Fast and Gentle

With OPTIM 1 there is no need to compromise between efficacy and being protected. With a fast broad-spectrum contact time it is one of the fastest and most effective cleaner & disinfectants. It is also safe and gentle for you and surfaces. OPTIM 1 gives you confidence that you are compliant and protecting your patients, staff and the environment; the perfect balance.

OPTIM has demonstrated effectiveness against viruses similar to Coronavirus Disease 2019 (COVID-19) on hard non-porous surfaces and non-invasive medical devices. This product can therefore be used against COVID-19 when used in accordance with the directions for use against Poliovirus on hard, non-porous surfaces, and non-invasive medical devices.

Fast Broad-Spectrum Disinfectant

Surfaces must remain wet for the entire contact time to achieve disinfection.

  • Adeno, Polio, Murine Noro in only 30 seconds according to EN 14476
  • Tuberculocidal & Fungicidal in 1 minute
  • Bactericidal according to EN 13727 & Virucidal according to EN 14476 in 30 seconds
  • Full virucide in 2 minutes according to RKI/DVV standard (Polio, Adeno, Murine Noro, SV40)
  • Effective in 1 minute according to EN 16615
  • Excellent wettability – stays wet long enough for contact times to elapse[1]

Demonstrated virucidal efficacy extends to new and emerging pathogens.

  • 30-second virucidal contact time applies to Novel Coronavirus (COVID-19), Severe Acute Respiratory Syndrome (SARS CoV) and Middle East respiratory syndrome (MERS CoV).

Effective One-Step Cleaner & Disinfectant

An effective 1 step cleaner disinfectant removes the organic debris while it disinfects[2].


Compatible with a wide range of hard, non-porous materials and surfaces[3].

Safe and Gentle

  • Free of artificial scents
  • Non-Toxic
  • Non-irritating to skin, eyes and respiratory system
  • No GHS hazard pictograms, signal words or statements
  • Leaves no active residue; doesn’t contribute to antimicrobial resistance

Environmentally Friendly

The active ingredient Hydrogen Peroxide breaks down into water and oxygen leaving no active residues which reduces the environmental impact.

OPTIM 1: One-Step Cleaner & Disinfectant. One-Minute TB Contact Time.

The Perfect Balance - No compromise between efficacy and low toxicity.

With a short broad-spectrum contact time, OPTIM 1 is one of the fastest and most effective cleaner & disinfectants. OPTIM 1 provides the confidence that you are compliant and mindful of patients, staff, equipment and the environment without compromise; the perfect balance. OPTIM 1 - One-step Surface Cleaner and Disinfectant. One Minute (TB) Contact Time. now available in EU.

Dental Advisor and Dr. John Molinari: Environmental Surface Cleaning Investigation Using SciCan’s OPTIM 1

Are your surfaces really clean?

Dr John Molinari tests alcohol and QUAT surface cleaners, as well as, OPTIM 1: One-Step Cleaner & Intermediate Disinfectant.

OPTIM 1 was the only disinfectant wipe to successfully clean and remove proteins with a single application.

Contact Time


Disinfecting Efficacy
EN 14348 - Tuberculocidal Mycobacteria Terrae 1
EN 14476 - Virucidal Non-enveloped Viruses Adeno 30 seconds
EN 16615 - Wipe Efficacy Test*** Bacteria Staphylococcus aureus,
Enterococcus hirae,
Psuedomonas aeruginosa
Yeast Candida albicans 1
EN 13727 - Bactericidal Bacteria Staphylococcus aureus,
Enterococcus hirae,
Psuedomonas aeruginosa
30 seconds
EN 13624 - Yeasticidal & Fungicidal Yeast Candida albicans 1
Fungi Aspergillus brasiliensis 1
Cleaning Efficacy
One-Step Cleaner
GHS Required Hazard Pictograms None Required
Non-Irritating to the Eyes Yes
Non-Irritating to the Skin Yes

* Contact time in minutes unless otherwise specified.
*** EN 16615 is a required EU standard to test the efficacy of the wiping mechanism.

Order Information

Ready-to-use Pre-saturated Wipes
OPTEU1-12W RTU Wipes 15 x 18 cm (12 x 160 sheets/case)
OPTEU1-W10x10 RTU Wipes 25 x 25 cm (12 x 60 sheets/case) - Backordered until August
OPTEU1-4x4 1 case of 4 x 4 Litres - Backordered
Additional Items
FND30 Pump for 4 Litre bottle



Find answers to frequently asked questions about OPTIM 1 here


Frequently Asked Questions for OPTIM 1

What is Accelerated Hydrogen Peroxide?

It is OPTIM 1’s active ingredient. Accelerated hydrogen peroxide is a synergistic blend of commonly used ingredients that are listed on the Environmental Protection Agency (EPA) Inerts List, the FDA GRAS list and Code of Federal Regulations (CFR) 21 Food Additives List, that when combined with low levels of hydrogen peroxide, dramatically increase its germicidal potency and cleaning performance.

Which surfaces can be cleaned and disinfected by OPTIM 1?

OPTIM 1 has been tested to be compatible with hard surfaces, including but not limited to dental chairs, stools, lights and counter tops if used according to our instructions for use on the label.

Surfaces that are composed of brass, copper, or other ferrous metals and soft plastic may show signs of discoloration or damage if not used as directed. Anodized aluminum (often used on handpieces) and carbon tipped instruments should be avoided. Please refer to the product label for the Instructions for Use.

Can OPTIM 1 be used to disinfect my dental chairs?

Yes, OPTIM 1 can be used to disinfect your dental chairs.1 However, it is important to remember that it is best practice to rinse all surfaces weekly with water to prevent surfactant build.

1 John Molinari, Ph.D., Peri Nelson, B.S. Effect of OPTIM* 1 on Tensile Properties of Dental Chair Fabrics*. Ann Arbor: Dental Advisor, 2016.

What is OPTIM 1’s shelf life?

OPTIM 1 has a two year shelf life from date of manufacture. The expiration date is listed on each container.

How do I properly dispose of OPTIM 1?

OPTIM 1 liquid can be poured directly down the drain. There is no need to dilute it with water since hydrogen peroxide breaks down into water and oxygen. Wipes should be disposed of in the trash after use; do not flush them down the toilet. The empty container should be recycled and if recycling is not available it can be discarded in the trash.

If the wipes have been used on surfaces where blood or body fluids were present, they should be disposed of according to federal, state and local regulations for infectious waste disposal.

Does OPTIM 1 have any special storage requirements?

OPTIM 1 should be stored in a cool dry area, away from direct sunlight and heat, and inaccessible to small children.2

2 OPTIM 1 Safety Data Sheet

What is OPTIM 1 contact time, and what does that mean?

OPTIM 1 contact time is one-minute. That means that the surface must remain wet for 1 minute in order for disinfection to occur. In Germany, according to the RKI/DVV standard, OPTIM has a 2-minute Fully Virucidal contact time.

Are any of the ingredients in OPTIM 1 carcinogenic?

No, all of the ingredients in OPTIM 1 are on the Environmental Protection Agency (EPA) Inerts List, the FDA GRAS list and Code of Federal Regulations (CFR) 21 Food Additives List.

Do I need to wear personal protective equipment when disinfecting clinical contact surfaces?

Yes, you should always wear appropriate personal protective equipment such as utility gloves when cleaning and disinfecting contaminated surfaces to protect against pricks and pokes.3 However, as stated in OPTIM 1’s Safety Data Sheet, PPE is not required to handle the product, particularly in non-clinical settings, because it is not irritating to the skin.

3 CDC, “Guideline for Disinfection and Sterilization in Healthcare Facilities” CDC. 2003, 26.

Can OPTIM 1 be used to clean surfaces?

Yes, OPTIM 1 has been tested as a one-step cleaner disinfectant, meaning it cleans your surfaces as it disinfects. Please refer to the product label for the Instructions for Use to learn how to use our product as a one-step cleaner disinfectant.

Is OPTIM 1 an intermediate level disinfectant?

Yes, OPTIM 1 has a one-minute efficacy claim according to EN EN13727 (bacteria), EN 13624 (Yeasts & Fungi), EN 14476 (viruses), EN 14348 (tuberculosis causing mycobacteria) and EN 16615

Why doesn’t OPTIM 1 have any of the new GHS hazard pictograms?

You may have noticed many disinfectants having new labels that include hazard pictograms they didn’t have before. This is because the revised hazard communication standard (HCS) of the new globally harmonized standard (GHS) has specific criteria for each health and physical hazard, and establishes both hazard classes and hazard categories. The previous HCS did not include categories for most of the health hazards covered by the GHS HCS, so this new approach provides the consumer with more information for awareness and that can be used to address the hazard.4

As with the old criteria, OPTIM 1 has been classified as non-hazardous in accordance with GHS HCS and therefore does not require any hazard pictograms, signal words or statements.5

4 Regulation (EC) No. 1272/2008 on Classification, Labelling and Packaging of Substances and Mixtures (CLP)

5 OPTIM 1 Safety Data Sheet

Is the efficacy or stability of OPTIM 1 affected if the product is frozen?

Freeze–Thaw studies have been conducted on OPTIM 1 to ensure that freezing will not have a negative effect on the stability & efficacy of AHP. If product is frozen, simply allow the product to thaw at room temperature. Once the product is completely thawed, shake to ensure the product has not separated into different phases prior to first use of the bottle.

Can OPTIM 1 be mixed with other chemicals?

It is never advisable to mix different chemical products. OPTIM 1 should never be mixed with any other chemicals.

I recently switched to OPTIM 1 after using a QUAT based product. What is causing the musty odor & film left on the surfaces?

Quaternary Ammonium Compound (QUATs) based products leave residual chemistry on surfaces. OPTIM 1 will remove the residual chemistry that has been left on the surface; however, there may be several layers of residual chemistry to remove. The odor and film you are experiencing is caused by the QUATs reacting to OPTIM 1 removing it. It may take between 5 and 10 days of OPTIM 1 use before the odor and film disappear.

To prevent this from happening we recommend cleaning your surfaces with soap and water before switching to a new disinfectant.

Can OPTIM 1 be used to sanitize and disinfect children’s toys in dental clinics?

Yes, OPTIM 1 has been classified as non-hazardous by the GHS hazard communications standard, category 4. However, as children’s toys do have the possibility to come in contact with children’s mouths, the toy must be rinsed with potable water once disinfected.

Can all disinfectants clean and disinfect in one-step?

No. Organic matter (food, blood or body fluid) on the surface forms a barrier that can either increase the contact time required to reach and kill the germs, or prevent their contact entirely.

OPTIM 1 is effective in the presence of organic matter, meaning it is a one-step cleaner and disinfectant. To ensure this, OPTIM 1 has been tested in the presence of organic matter called serum. The serum test measures the product efficacy when organic soils are present. To check whether a disinfectant has been tested with serum, check the label to see if it says “tested in the presence of 5% serum load.”

How do disinfectants perform against antibiotic resistant bacteria?

Antibiotic resistance does not mean chemical resistance. These bacteria have developed resistance to antibiotics pertaining to human clinical situations. This does not mean that these strains are resistant to chemical disinfection. Most disinfectants, such as OPTIM 1, are tested against antibiotic resistant strains such as VRE, MRSA etc. These are shown on the label claims.

Do some disinfectants continue to sanitize for up to 24 hours, even after the surface is dry?

No. Products that make this claim leave behind active residues, however the surface needs to be wet for those active residues to continue to disinfect. These products leave behind residues because they don’t readily degrade, but rather build up in the environment. OPTIM 1 does not leave behind any active residues.

Is the use of disinfectants contributing to antimicrobial resistance?

Yes, studies show that disinfectants that leave an active residue behind on surfaces contribute to the development of antimicrobial resistance, a major global health crisis we are facing.

It is best practice to look for disinfectants with active ingredients that readily degrade into the environment such as hydrogen peroxide, such as OPTIM 1. Accelerated hydrogen peroxide breaks down into water and oxygen leaving no active residues behind, ensuring that it won’t contribute to antimicrobial resistance.6

6 Ulas Tezel, Spyros G. Pavlostathis, “Role of Quaternary Ammonium Compounds on Antimicrobial Resistance in the Environment,” in Antimicrobial Resistance in the Environment, First Edition ed. Patricia L. Keen et al. (Toronto: John Wiley & Sons, Inc, 2011), 349-387.https://www.researchgate.net/publication/230547727_Role_of_Quaternary_Ammonium_Compounds_on_Antimicrobial_Resistance_in_the_Environment

Does it matter which pathogens (viruses, bacteria, etc.) an intermediate level disinfectant can kill?

Yes. Disinfectant product labels often include a long list of pathogens that it can kill, but which ones are the most important? Pathogens are divided into classes, and each class has a surrogate organism that is the gold standard or more difficult to kill pathogen in that class, for example:

Class Surrogate Organism
Vegetative Bacteria Pseudomonas aeruginosa, Staphylococcus aureus and Enterococcus hirae
Viruses Poliovirus, Adenovirus and Murino Norovirus (+ SV40 for RKI/DVV)
Mycobacteria Mycobacterium terrae (Tuberculosis)
Fungi Aspergillus Brasiliensis
Bacterial Spores Bacillus subtilis and Clostridium sporogenes

When choosing a disinfectant, it is important to make sure that it can inactivate the more difficult pathogens so that you can feel confident that you are killing virtually everything.

What color and scent does OPTIM 1 have?

For environmental and health reasons there are no dyes or fragrances added to OPTIM 1. Most fragrances used are classified as volatile organic compounds (VOCs) which are known as one of the leading causes of fragrance sensitivity and negative affects to indoor air quality.

I understand that the pH of accelerated hydrogen peroxide is acidic. Will this cause irritation or serious damage to unprotected skin?

No. Accelerated hydrogen peroxide is acidic because it contains small amounts of food acids. Food acids are not toxic and found naturally in food, such as vinegar (acetic acid), citrus fruits (citric acid), Vitamin C (ascorbic acid), and Coca-Cola(phosphoric acid). If food acids are carefully formulated, like they are in OPTIM 1, they do not cause irritation.7

7 VIROX, “Disinfection Digest: pH: Is it an appropriate indicator of product safety?,” VIROX. https://cdn2.hubspot.net/hubfs/241248/ph_is_it_an_appropriate_indicator_of_product_safety_HH.pdf (accessed December 2016).

Is OPTIM 1 safe for disinfecting VPS impressions?

Yes. A study was done to test the effects of OPTIM on VPS impression materials’ surface detail and dimensional stability. The study found that when used in accordance with our instructions for use there was no damage done to the impression.8

8 Dr. Raghunath Puttaiah, “Compatibility of Hydrogen Peroxide-Based Surface and Immersion Disinfectants with Elastomeric Impression Materials.” Toronto: Spectrum Dialogue Volume 12, Issue 2 (2013), 66.

Is OPTIM 1 (or any intermediate level disinfectant) effective against C. difficile?

No, no intermediate level disinfectants can kill C. difficile. However, accelerated hydrogen peroxide based products like OPTIM 1 can be used as a preventative method against C. difficile outbreaks and related Hospital Acquired Infections (HAI). A study done by the American Journal of Infection Control (AJIC) concluded that daily use of accelerated hydrogen peroxide disinfectant was superior to using a cleaner alone because it resulted in significantly reduced rates of HAIs caused by C. difficile.9

9 M.J. Alfa et al., “Use of a daily disinfectant cleaner instead of a daily cleaner reduced hospital-acquired infection rates,” AJIC Volume 43 (2015), 141-6.

Save this product for later